View STU9NC80Z_956616.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STU9NC80Z STU9NC80ZI
N-CHANNEL 800V - 0.82 - 8.6A Max220/I-Max220 Zener-Protected PowerMESHTMIII MOSFET
TYPE STU9NC80Z STU9NC80ZI
s s s s s s
VDSS 800 V 800 V
RDS(on) <0.9 <0.9
ID 8.6 A 8.6 A
TYPICAL RDS(on) = 0.82 EXTREMELY HIGH dv/dt CAPABILITY GATE-TO-SOURCE ZENER DIODES 100% AVALANCHE TESTED VERY LOW INTRINSIC CAPACITANCES GATE CHARGE MINIMIZED
1
2
3
Max220
I-Max220
DESCRIPTION The third generation of MESH OVERLAYTM Power MOSFETs for very high voltage exhibits unsurpassed on-resistance per unit area while integrating back-to-back Zener diodes between gate and source. Such arrangement gives extra ESD capability with higher ruggedness performance as requested by a large variety of single-switch applications. APPLICATIONS s SINGLE-ENDED SMPS IN MONITORS, COMPUTER AND INDUSTRIAL APPLICATION s WELDING EQUIPMENT ABSOLUTE MAXIMUM RATINGS
Symbol VDS VDGR VGS ID ID IDM (1) PTOT IGS VESD(G-S) dv/dt(q) VISO Tstg Tj Parameter STU9NC80Z Drain-source Voltage (VGS = 0) Drain-gate Voltage (RGS = 20 k) Gate- source Voltage Drain Current (continuos) at TC = 25C Drain Current (continuos) at TC = 100C Drain Current (pulsed) Total Dissipation at TC = 25C Derating Factor Gate-source Current Gate source ESD(HBM-C=100pF, R=15K) Peak Diode Recovery voltage slope Insulation Winthstand Voltage (DC) Storage Temperature Max. Operating Junction Temperature --65 to 150 150
(1)ISD 8.6A, di/dt 100A/s, VDD V (BR)DSS, Tj T JMAX (*)Limited only by maximum temperature allowed
Value STU9NC80ZI 800 800 25 8.6 5.4 34.4 160 1.28 50 4 3 2000 8.6(*) 5.4(*) 34.4(*) 55 0.44
Unit V V V A A A W W/C mA KV V/ns V C C
(*)Pulse width limited by safe operating area
Sep 2000
1/10
STU9NC80Z/STU9NC80ZI
THERMAL DATA
Max220 Rthj-case Rthj-amb Rthc-sink Tl Thermal Resistance Junction-case Max Thermal Resistance Junction-ambient Max Thermal Resistance Case-sink Typ Maximum Lead Temperature For Soldering Purpose 0.78 30 0.1 300 I-Max220 2.27 C/W C/W C/W C
AVALANCHE CHARACTERISTICS
Symbol IAR EAS Parameter Avalanche Current, Repetitive or Not-Repetitive (pulse width limited by Tj max) Single Pulse Avalanche Energy (starting Tj = 25 C, ID = IAR, VDD = 50 V) Max Value 8.6 400 Unit A mJ
ELECTRICAL CHARACTERISTICS (TCASE = 25 C UNLESS OTHERWISE SPECIFIED) OFF
Symbol V(BR)DSS Parameter Drain-source Breakdown Voltage Test Conditions ID = 250 A, VGS = 0 ID = 1 mA, VGS = 0 VDS = Max Rating VDS = Max Rating, TC = 125 C VGS = 20V Min. 800 1 1 50 10 Typ. Max. Unit V V/C A A A
BVDSS/TJ Breakdown Voltage Temp. Coefficient IDSS IGSS Zero Gate Voltage Drain Current (VGS = 0) Gate-body Leakage Current (VDS = 0)
ON (1)
Symbol VGS(th) RDS(on) ID(on) Parameter Gate Threshold Voltage Static Drain-source On Resistance On State Drain Current Test Conditions VDS = VGS, ID = 250A VGS = 10V, ID = 4.7A VDS > ID(on) x RDS(on)max, VGS = 10V 8.6 Min. 3 Typ. 4 0.82 Max. 5 0.9 Unit V A
DYNAMIC
Symbol gfs Ciss Coss Crss Parameter Forward Transconductance Input Capacitance Output Capacitance Reverse Transfer Capacitance Test Conditions VDS > ID(on) x RDS(on)max, ID =4.7A VDS = 25V, f = 1 MHz, VGS = 0 Min. Typ. 13 3500 230 25 Max. Unit S pF pF pF
2/10
STU9NC80Z/STU9NC80ZI
ELECTRICAL CHARACTERISTICS (CONTINUED) SWITCHING ON (RESISTIVE LOAD)
Symbol td(on) tr Qg Qgs Qgd Parameter Turn-on Delay Time Rise Time Total Gate Charge Gate-Source Charge Gate-Drain Charge Test Conditions VDD = 400V, ID = 4.5A RG = 4.7 VGS = 10V (see test circuit, Figure 3) VDD = 640V, ID = 9 A, VGS = 10V Min. Typ. 35 16 72.2 19.5 24.3 101 Max. Unit ns ns nC nC nC
SWITCHING OFF (INDUCTIVE LOAD)
Symbol tr(Voff) tf tc Parameter Off-voltage Rise Time Fall Time Cross-over Time Test Conditions VDD = 640V, ID = 9 A, RG = 4.7, VGS = 10V (see test circuit, Figure 5) Min. Typ. 32 42 67 Max. Unit ns ns ns
SOURCE DRAIN DIODE
Symbol ISD ISDM (2) VSD (1) trr Qrr IRRM Parameter Source-drain Current Source-drain Current (pulsed) Forward On Voltage Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current ISD = 8.6 A, VGS = 0 ISD = 9 A, di/dt = 100A/s, VDD = 100V, Tj = 150C (see test circuit, Figure 5) 730 7.2 19.5 Test Conditions Min. Typ. Max. 8.6 34.4 1.6 Unit A A V ns C A
GATE-SOURCE ZENER DIODE
Symbol BVGSO T Rz Parameter Gate-Source Breakdown Voltage Voltage Thermal Coefficient Dynamic Resistance Test Conditions Igs= 1mA (Open Drain) T=25C Note(3) IGS = 50 mA, VGS = 0 Min. 25 1.3 90 Typ. Max. Unit V 10-4/C
Note: 1. Pulsed: Pulse duration = 300 s, duty cycle 1.5 %. 2. Pulse width limited by safe operating area. 3. VBV = T (25-T) BVGSO(25)
PROTECTION FEATURES OF GATE-TO-SOURCE ZENER DIODES The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device's ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to souce. In this respect the 25V Zener voltage is appropiate to achieve an efficient and cost-effective intervention to protect the device's integrity. These integrated Zener diodes thus avoid the usage of external components.
3/10
STU9NC80Z/STU9NC80ZI
Safe Operating Area For Max220 Safe Operating Area For I-Max220
Thermal Impedance For Max220
Thermal Impedance For I-Max220
Output Characteristics
Transfer Characteristics
4/10
STU9NC80Z/STU9NC80ZI
Transconductance Static Drain-source On Resistance
Gate Charge vs Gate-source Voltage
Capacitance Variations
Normalized Gate Threshold Voltage vs Temp.
Normalized On Resistance vs Temperature
5/10
STU9NC80Z/STU9NC80ZI
Source-drain Diode Forward Characteristics
6/10
STU9NC80Z/STU9NC80ZI
Fig. 1: Unclamped Inductive Load Test Circuit Fig. 2: Unclamped Inductive Waveform
Fig. 3: Switching Times Test Circuit For Resistive Load
Fig. 4: Gate Charge test Circuit
Fig. 5: Test Circuit For Inductive Load Switching And Diode Recovery Times
7/10
STU9NC80Z/STU9NC80ZI
Max220 MECHANICAL DATA
DIM. MIN. A A1 A2 b b1 b2 c D D1 D2 D3 e E L L1 4.3 2.2 2.9 0.7 1.25 1.2 0.45 15.9 9 0.8 2.8 2.44 10.05 13.2 3 mm TYP. MAX. 4.6 2.4 3.1 0.93 1.4 1.38 0.6 16.3 9.35 1.2 3.2 2.64 10.35 13.6 3.4 0.354 0.031 0.110 0.096 0.396 0.520 0.118 MIN. 0.169 0.087 0.114 0.027 0.049 0.047 0.18 0.626 inch TYP. MAX. 0.181 0.094 0.122 0.036 0.055 0.054 0.023 0.641 0.368 0.047 0.126 0.104 0.407 0.535 0.133
D3
D2
D1
A
A2
C
D
b1
b2
E
b e
L1 L
A1
P011R
8/10
STU9NC80Z/STU9NC80ZI
I-Max220 MECHANICAL DATA
DIM. MIN. A A1 A2 b b1 b2 c D D1 D2 D3 e E L L1 4.3 2.6 1.95 0.7 1.25 1.2 0.45 15.9 12.5 0.6 1.75 2.44 10.05 13.2 3 mm TYP. MAX. 4.6 2.75 2.15 0.93 1.4 1.38 0.6 16.3 12.9 1 2.15 2.64 10.35 13.6 3.4 MIN. 0.169 0.102 0.077 0.027 0.049 0.047 0.017 0.626 0.492 0.023 0.069 0.096 0.396 0.520 0.118 inch TYP. MAX. 0.181 0.108 0.084 0.036 0.055 0.054 0.023 0.641 0.508 0.039 0.084 0.104 0.407 0.535 0.133
P011S
9/10
STU9NC80Z/STU9NC80ZI
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics (c) 2000 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com
10/10

▲Up To Search▲

Price & Availability of STU9NC80Z

	To Download STU9NC80Z Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .